2008 Jeep Patriot Lower Control Arm

Front Suspension Control Arm Problem Of The 2015 Jeep Patriot

Jeep had 40,000 miles on it and was making a weird noise when driving on the highway. I thought it was tires, so I got new tires and they told me the ball joints were loose and needed to be replaced. They quoted it and said that without fixing it, it would wear down my tires faster. I brought my car in for inspection at another shop and they were surprised, but they said the ball joint assemblies needed to be replaced as they were loose and rusted out and that they need to do both control arms because of how the Jeeps are bit and explained it thoroughly. They also said they could not estimate how much of a life they had left, but that it would be best to fix it before it broke. I had them replace the front control arms and ball joint assemblies.

What To Look Out For When Dealing With Control Arm Issues

If a control arm is damaged, the suspension alignment will be compromised. In addition, rubber bushings are adversely affected by heat and by petroleum products . It is important to periodically inspect the control arm bushings to make sure they are free from grease or oil. Also, in order to replace a control arm, the vehicle needs to be safely raised and supported on a hoist or a jack and jack stands.

Front Suspension Control Arm Problem Of The 2010 Jeep Patriot

Front crossmember is completely rotted out. Chrysler extended the warranty for this to 10 years to include inspections rather than recall to correct this problem. Since I bought this Jeep used I was not informed this could be a problem or that I was entitled to inspections to look for this problem. I originally thought this was a control arm issue but when the vehicle was put on the hoist, looking at it from below, the front crossmember has nearly completely rusted out. No other parts of the underside of the vehicle have experienced this extent corrosion damage. This is clearly a defect in materials of construction or choice of surface coating for this part. This is an extremely dangerous condition which consumers may be completely unaware of, unless they were the original purchaser. Dealership service department said they had a customer make it to the dealership for the same problem just to have the crossmember give way, dropping the the engine onto the ground in the parking lot. Unbelievable! I wish I had photos from when I originally had it on the hoist, but I didn’t get them. It is at the dealership now. Chrysler initially said they would try to offer some “good will” but have since rejected this due to the $2350. 00 estimate for repair. No wonder they weren’t recalled. Shame on you Chrysler!.

Also Check: New England Patriots Store Boston

Control Arm And Strut Torque

Only show this user

1. Place the lower control arm into the front suspension crossmember . 2. Insert the rear bolt up through the crossmember and lower control arm . 3. Install, but do not fully tighten, the nut on the rear bolt attaching the lower control arm to the crossmember . 4. Install, but do not fully tighten, the front bolt attaching the lower control arm to the crossmember. 5. With no weight or obstruction on the lower control arm, tighten the lower control arm rear mounting bolt nut to 183 N·m . 6. With no weight or obstruction on the lower control arm, tighten the lower control arm front pivot bolt to 183 N·m . 7. Install the ball joint stud into the knuckle , aligning the bolt hole in the knuckle boss with the groove formed in the side of the ball joint stud. 8. Install a NEW ball joint stud pinch bolt and nut . Tighten the nut to 82 N·m .

“Nothing is either good or bad, but thinking makes it so.”- William Shakespeare

When Replacing A Control Arm Keep In Mind:

• The number of control arm types vary from vehicle to vehicle depending on the design of the vehicle suspension.
• Control arms should be replaced in pairs arms on both sides of a front or rear axle if the reason for replacement is worn control arm bushings or a worn ball joint.
• All other suspension components should be inspected when control arms are replaced because looseness, damage, or excessive wear in other parts of the suspension system will make it impossible to perform a wheel alignment after the control arms are replaced.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Don’t Miss: Are There Any Republicans On The House Intelligence Committee

Front Suspension Control Arm Problem

Never received extended warranty information on front and rear crossmember corrosion . Have all required maintenance at dealer. They never mentioned the extended coverage nor did they tell me after any of the service there was a rust issue. Now they refuse to cover this repair. I also have the lifetime mopar maximum care. They also won’t cover because they say the part failure is due to rust. Tge parts requiring replacement should all be covered. They are:rear crossmember – rear upper and lower control arms – both rear calipers.

Front Suspension Control Arm Problem Of The 2017 Jeep Patriot

The contact owns a 2017 Jeep Patriot. While driving 65 mph, the steering wheel vibrated and the vehicle pulled to the right after a stop. Also, the tire pressure warning indicator was illuminated. The vehicle was taken to kunes country Chrysler Dodge Jeep ram of oregon, 601 gale street, oregon, IL 61061) where it was diagnosed with a bent rim. The exact rim was unknown however, it was replaced. The contact stated that the failure persisted and the vehicle was taken back to the dealer where it was diagnosed that the front passenger side lower control arm was bent. The control arm and axle shaft were replaced however, the failure persisted. The vehicle was taken back to the dealer a third time and was awaiting diagnoses. The contact mentioned that the headlights were also turned towards the ground and the dealer adjusted the direction and replaced the passenger side head lamp. The contact also stated that she was informed by the dealer of a blown tire belt that was replaced, but was unaware of which tire. The manufacturer was not made aware of the failures. The failure mileage was approximately 3,300.

Also Check: Trump 1998 Snopes

How Are Control Arm Issues Diagnosed

A technician may diagnose a worn lower control arm during a test drive of the vehicle. The condition may also present itself during a bounce test, where the technician will press down firmly on one corner of the vehicle to bounce the suspension and pivot the control arms. A damaged or bent control arm may show up during a four wheel suspension alignment since the control arm determines the position and angle of the wheel.

Jeep Patriot Front Lower Control Arm

See below our 2008 Jeep Patriot Front Lower Control Arm inventory

Also Check: 114th Congress Senate

Front Lower Control Arms

“Nothing is either good or bad, but thinking makes it so.”- William Shakespeare

Update

“Nothing is either good or bad, but thinking makes it so.”- William Shakespeare

Update

Jeep Patriot Control Arms

• Replaces

• Kit Includes: Rear Upper Control Arms
• Kit Includes: Rear Lower Locating Arms
• Quantity: 4 Piece

Need your part faster? Choose expedited shipping at checkout.

Guaranteed To Fit

Highest quality, direct fit replacement auto parts enforced to the strictest product standards.

USA Customer Support

Exceeding customers’ expectations, our team of passionate auto enthusiasts are here to help.

Instructional Video Library

You May Like: Patriots Ticket Exchange Account Manager

Always Thinking About The Customer

With Mevotech, customers never get re-boxed parts from other manufacturers. Instead, they get the best original Mevotech parts. Whether its designing premium parts, saving you time with bundled hardware and pre-assembled parts, or delivering support when and where their customers need it, Mevotech works hard to keep the needs of their customers in mind.

Ck : Moog Problem Solver

Starting with the CK and K. Whether you see a “K” designation or a “CK” designation, you are getting the same part. The CK and K are Moogs Premium line of control arms. Utilizing their “problem solver” technology, these control arms address common factory design issues providing a better than the original replacement for your vehicle. Most CK and K control arms include ball joints that are powder coated metal with gusher bearings giving them a long life. Many of these ball joints are serviceable and have grease fittings. The CK and K arms also have problem solver bushings and a precise fit and form for easy installation.

Read Also: Dodge Dealership Mcalester Ok

How Is A Control Arm Replaced

A technician will replace a lower control arm by first lifting and supporting the vehicle in the air on a hoist and removing the wheel and tire. A lower control arm must be disconnected from the lower ball joint and from the vehicle frame or body. An upper control arm is disconnected from the strut tower on the body and from the top of the steering knuckle. Some control arms come with bushings permanently installed in them, while others require the bushings to be installed. It is common to replace related components – ball joints, tie rod ends, sway bar links – at the same time that a control arm is replaced.

Can I Replace The Control Arm Myself

Replacement of a control arm is generally an intermediate DIY repair. On some vehicles, the control arms come with the bushings already installed. On other vehicles, the bushings need to be pressed into their housings on the control arm before installation into the vehicle. In this case, the repair will be more difficult. Also, this repair requires that the vehicle be safely lifted and supported with a jack and jack stands. Failure to do so in a safe manner can result in serious injury or death.

You May Like: Trump Popularity Among Republicans

When To Consider Replacing A Control Arm:

The structural portion of the control arm can last the life of the vehicle except for cases of corrosion or crash damage. However, the rubber bushings and the ball joint in a control arm have a limited life. A mechanic should investigate if you notice:

• Wheel alignment difficulties. Should the bushings, or the ball joint, in a control arm be worn, it will be impossible to properly align the vehicle. The worn components, or the entire arm, must be replaced.
• Vehicle wont track straight or pulls to one side. A car will not track straight and may require constant steering correction if there is a worn, bent, or loose control arm.
• Clunking or squeaking noise. A loose control arm, or a control arm with dried out, rotted, or loose bushings, may move enough to cause detectable noise from the suspension as you go over bumps in the road.
• Vehicle pulls to one side only when braking. Worn bushings or ball joints can allow control arm to shift when braking, causing the vehicle to pull to one side. Although, this could also be caused by brake calipers.

Can I Drive With A Control Arm Problem

If the control arm on a vehicle is damaged in a crash or impact with a pothole or parking block, the suspension will be out of alignment and cause uneven tire wear and poor vehicle handling. The control arm should be replaced as soon as possible. If the control arm bushings are worn, the result will be an annoying squeak when the car goes over bumps. In this case, the car can be driven. But if the bushings wear out considerably, metal-on-metal contact may happen between the control arm and the bushing bracket. This can cause further suspension damage and the control arm or bushing should be replaced.

Read Also: Stream Patriots Game Cbs

How Does The Control Arm Work

The control arm is connected on one end to the steering knuckle by a ball and socket called a ball joint. It is attached at the other end to the vehicle frame or body. When a car goes over a bump, the control arm pivots up and down with the wheel and allows the vehicle body to remain stable. On the frame/body side, the control arm has a bushing that allows it to pivot.

How Do Mechanics Replace A Control Arm

• The vehicle is raised and supported on steel jack stands, and the wheel and tire assembly is removed.
• Stabilizer bar links are detached from the control arm, if applicable. ABS wiring to the wheel speed sensor, if routed along the arm, is disconnected.
• Control arm mounting bolts are detached from the frame and from the axle carrier if the control arm is in the rear.
• For front control arms connected to the steering knuckle via a ball joint, the nut is removed from the ball joint stud and the stud is pushed through the steering knuckle to free the arm.
• The arm is lowered from the vehicle and examined by the mechanic to confirm that the noise, or other problem, actually originated from a defect in the arm.
• The new arm is installed using new mounting bolts if required by the service manual. In many cases, the fasteners must be tightened with the vehicle weight on the suspension in order to ensure the bushings are in a neutral, or resting, position.
• The vehicle is lowered and road tested to confirm the problem is resolved. Replacing a control arm will change the vehicle alignment settings and the mechanic will refer you to a professional alignment shop to have the vehicle alignment set to factory specifications.

Also Check: My Patriot Supply Complaints

What Is A Control Arm

The control arm connects the steering knuckle to the frame or body of a vehicle. The wheel is held on to a hub connected to the steering knuckle. The knuckle allows the wheel to steer left and right and is attached to the control arm. The control arm allows allow the wheel to travel up and down over bumps and helps to position the wheel in the proper alignment.

Jeep Patriot Rear Lower Control Arm

See below our 2008 Jeep Patriot Rear Lower Control Arm inventory

You May Like: Donald Trump Interview 1998 People Magazine

Front Suspension Control Arm Problem Of The 2007 Jeep Patriot

Tl- the contact owns a 2007 Jeep Patriot 4×4. The contact stated that while driving at 55 mph, a clicking sound was heard. The failure occurred constantly. The vehicle was taken to a dealer where it was diagnosed that the rear lower control arm needed to be replaced. The vehicle was not repair. The manufacturer was notified of the failure. The approximate failure mileage was unknown. Jo.

Mevotech Auto Parts: Fix It Once And Fix It Right

Mevotech has been revolutionizing the automotive aftermarket for over thirty years. Since 1982, they have been learning and innovating to ensure they are creating top-quality, technologically advanced automotive parts while delivering the best customer service and support in the industry. Specializing in Suspension and Steering systems, along with Drivetrain and Wheel parts, Mevotech delivers exceptional service and broad vehicle coverage.

Recommended Reading: Washington Post Republican Or Democrat

What Is The Difference Between Moog R Series And Ck Control Arms

CK, K or RK? We here at Diverse Suspension Technologies get this question a whole lot. If you are putting parts on your vehicle, you want to know exactly what you are installing. It can be hard to do that with all of these letter designations. So here is all that you need to know to clear up the confusion.

Short Answer: R Series is a value-driven replacement part while the CK Series incorporates Moog’s premium Problem Solver components for a better than OE upgrade.

Front Suspension Control Arm Problem Of The 2009 Jeep Patriot

Loud clunking noise from left front wheel area while driving and making turns. . Visual inspection revealed crossmember seriously rusted and corroded at upper control arm area. Several major cracks in subframe due to rust through compromising vehicle stability. Complaints made to Chrysler and the dealership with no resolution. Chrysler was well aware of the issue and put out a service bulletin pertaining to the problem. Service bulletin 23-007-17 rev b. Extending warranty coverage for only 10 years. I believe Chrysler deliberately put a 10 year cap on these parts to limit their responsibility because they were well aware of the severe rusting issue and knew other vehicles would soon be effected. I ‘am now facing a repair bill of over $1000. 00 and that does not include anything else that needs to be replaced because of this parts failure.

You May Like: What Is The Lapel Pin Democrats Are Wearing