Remove The Existing Light Fixture
- Make sure electricity to circuit is turned off and carefully remove the glass shade or globe from the old light fixture.
- Unscrew the retaining nut or screws that hold the fixture to the ceiling.
- Lower the fixture and disconnect the wires by twisting off the plastic connectors from the ends of the wires.
Install New Outlet Box
Remove a knockout on the outlet box and attach a cable clamp. Feed the supply line through the clamp so the line extends 6 inches from the box. Guide the outlet box through the opening in the ceiling and align the box with the u-bolt brace. If the hole in the ceiling is too small, use a keyhole saw to enlarge it. Attach the outlet box directly to the brace with the washers and nuts provided. Please note that the bottom of the box must be recessed a minimum of 1/16 inch into the ceiling.
Create A Balanced Look
The positioning of downlights is important to create a balanced look. This ensures that there are no shadows and the lights produce maximum light possible to brighten up the given space. The starting point should be at least 2 feet away from the edge of walls. It is then crucially important to distribute the lights evenly across the room.
Also Check: Number Of Times Republicans Voted To Repeal Obamacare
Attach The Blades And Lights
- Attach each fan blade to a blade iron . Then, fasten the blade irons to the motor with the screws provided.
- Plug the fan’s light-fixture housing into the wire hanging from the underside of the fan’s motor.
- Install the shades and lightbulbs.
- Screw the plastic holder for the remote control to the wall beside the wall switch.
Best With Remote: Minka
Diameter: 52 inches | Material: Metal, plastic| Lighting: Integrated LED light source | Control Type: Remote control | Mounting Type: Downrod
-
Hangs from a downrod
-
Relatively expensive
Minka-Aire’s 52-inch Light Wave is a modern fixture with three elegantly curved blades. This sleek remote-controlled ceiling fan does more than circulate airit offers ample overhead lighting by way of a long-lasting, dimmable LED bulb. Plus, it enhances the design of your home.
You can choose from four stunning finishes: Koa wood, futuristic silver, minimalist white, or a chic matte black. Since this fan hangs from a downrod, you’ll want to make sure you have enough clearance before ordering it. That said, it’s notably easy to install.
“It provides very good airflow on the two higher settings but does not seem to move much air on the lowest setting. We feel that other fans weve used at hotels or friends homes were more cooling, though potentially far more expensive as well.”Tierney McAfee, Product Tester
Don’t Miss: People Magazine 1998 Trump Interview
Attach New Electrical Box
- Feed the electrical cable coming from the ceiling through the knockout hole in the pancake box.
- Set the box into the hole cut through the ceiling and press it tight against the underside of the joist.
- Attach the box to the joist with the two 1 1/2-inch No. 10 hex-head screws provided. Drive in the screws with a drill/driver equipped with a 5/16-inch nut-driver tip.
- Wrap the cable’s bare copper wire around the grounding screw inside the box. Allow the wire end to hang down.
Best For Large Rooms: Three Posts Alistair Blade Led Standard Ceiling Fan With Remote Control
Diameter: 52 inches | Material: Manufactured wood, metal, glass| Lighting: Integrated 19 watt LED light| Control Type: Remote control | Mounting Type: Downrod
-
Relatively expensive
This five-bladed fixture for sale at Wayfair.com was made for large areas. Designed to deliver airflow to up to 360 square feet of space, it’s ideal for a living room, great room, or sizable master suite.
The integrated LED light is filtered by a frosted cover and will deliver up to 50,000 hours of illuminationlikely a lifetime’s worth. What’s more, both the light and the fan can be controlled with the included remote.
Don’t Miss: How Many Democrats And Republicans Are In The House
How To Shorten A Ceiling Fan Downrod
Ceiling fans no longer come in just black or white they are offered in a variety of finishes and styles that can draw the eye to the fan. Ceiling fans can complement your decor. They can become as indispensable to the interior design as a table lamp, so when you move, you move the ceiling fan with you. If the ceiling height in your new home is lower than your previous home, you can shorten your ceiling fan downrod to fit the room rather than purchase a new one.
1
2
Wrap the downrod in a towel or cloth. Insert the downrod into a vise. Rotate the downrod until the clevis pin openings in the sides on each end face upward toward the ceiling. Tighten the vise to ensure the downrod does not move.
3
Cut the downrod along the cut line, using a hacksaw. Smooth the cut edges, using a round file.
4
Measure 1/2-inch from the cut end of the downrod and mark that point, using a felt-tipped marker. Ensure the mark on the downrod lines up with the clevis pin opening on the end of the rod still in the vise.
5
Attach a 1/2-inch metal drill bit to a power drill. Position the drill bit over the mark you made at the end of the downrod. Drill straight through both sides the downrod to create a clevis pin opening.
6
Remove the shortened downrod from the vise.
Writer Bio
Assemble The Fan Components
- With the fan on the floor, feed the wires coming from the motor through the center of the canopy. Set the canopy on top of the motor.
- Next, pass the wires through the hollow down-rod pipe.
- Thread the down-rod pipe into the top of the motor. Use a wrench to tighten the square-head locking screw on the side of the pipe.
Tip: The pipe’s threads have a factory-applied coating. Don’t remove this coating it keeps the pipe from unscrewing.
Read Also: How Many States Are Controlled By Republicans
Essential Tips For Installing Led Downlights
- note:
LED lights have replaced the traditional lighting fixtures that used to hang down the ceiling. The sleek and elegant design of LED downlights has made them a popular choice nowadays. These lights shine out from the ceiling and have no visible fixtures providing a minimalist look.
Installing these lights saves you from the hassle of replacing lights every now and then. However, it is important to install them correctly for perfect lighting and safety. An LED light can only partly light up a room thereby multiple lights should be placed at the right distance to utilize space. Following these essential tips will save you from mishandling the LED downlights while installing them.
By Step Ceiling Fan Installation Guide
Hi. I’m Colby with Del Mar Fans & Lighting and I’m here to show you how to install a ceiling fan.
For this ceiling fan installation video, we used Casablanca fans.
To reduce the risk of personal injury and property damage, follow the safety rules below:
You May Like: Republicans In Senate 2018
Ceiling Fan Installation & Replacement
A new ceiling fan can help with ventilation and comfort in your home, yet installing one is not an easy task. You need to understand lighting and electrical work, and you also need to understand how to hang it safely. Thats why professional help is necessary. Apollo Home has a team of construction pros and electricians who can help with ceiling fan installation and replacement, so you can enjoy all of the perks of having a ceiling fan in your home.
If you want a ceiling fan, Apollo Home can help. Contact us for ceiling fan installation and replacement in Cincinnati and the surrounding communities by calling 268-8400. You can also contact us online.
Install Support Brace With U
Insert the support brace into the opening in the ceiling and position the brace between the nearest two joists. Turn the support brace with your hands until it lock into the joists. The teeth at the end of the brace will grip the joists and hold the brace in place. If needed, use a crescent wrench to finish tightening the brace. Place the u-bolt over the safety brace with screws provided.
Recommended Reading: Did The Parties Switch Platforms
Optimal Sizing Speed And Placement
Use this formula to find the best fan size for a rooms occupied space : Occupied space divided by 4 equals the blade span . Step blade span down a bit for rooms with low ceilings, and go wider if the ceilings are high.
Another good rule of thumb is to remember that blade spans of less than 36 inches are ideal for spaces smaller than 75 square feet, such as baths and breakfast nooks. Spans of 36 to 42 inches work in rooms of up to 225 square feet, like a dining room. Larger living rooms and bedrooms can handle 50- to 54-inch blades.
Make sure that the cubic feet of air that the fan moves per minute , measured at high speed, is near the top of its class. Some 52-inch fans, for instance, rate as low as 2,050 cfm, while others reach 7,800. High-cfm fans not only provide a better breeze, they usually have robust motors that will last longer and run more quietly.
For optimal performance, the fan should be hung at least 1 1/2 feet from the wall or a sloped ceiling, 7- to 10-feet from the floor, and at least 8 inches from the ceiling. Steer clear of hanging the fan too close to any lights, as rotating blades under a bulb will create an annoying flicker.
Where To Hang A Ceiling Fan
Choosing an installation site is as important as selecting the ceiling fan itself. The right location ensures your safety as well as the fan’s performance and efficiency. When selecting an installation site, consider the following details:
Also Check: How Many States Are Controlled By Republicans
Calculate Wattage For Lighting Up Space
Calculate the required wattage for lighting up the space so you may know how many LED downlights you will need. This is usually done by multiplying the square footage of the room by 1.5. Choose the right type of bulb and see its wattage. Divide the total wattage by the wattage of bulbs and you will know the number of lights to be installed. Also, it is wise to install more number of lower power LED lights to have an even distribution of light instead of higher power lights. It is true that LED downlights can only partly light up a room as the lumens and covering space is less. However, multiple lights placed in an area enable you to switch off or even dim the lights whenever you want.
Why Trust The Spruce
Theresa Holland is a freelance commerce writer with several years of experience covering home improvement and interior design. With a keen understanding of HVAC and a finger on the pulse of home decor, she knows how to find the best ceiling fans. Theresa has been writing for The Spruce since 2019 and also regularly contributes to Byrdie and MyDomaine.
Also Check: Did Trump Call Republicans Stupid In 1998
Remove Box And Cut New Hole
- Remove the old electrical box from the ceiling. If it’s nailed to a joist, pry it free with a flat bar. If it’s suspended from a bar, you may have to take off a metal plate to unscrew the box then pry the bar from the joists.
- Hold a 1/2-inch-thick pancake box against the ceiling, centered on a joist, and trace around it with a pencil.
- Cut along the line with a drywall saw.
Tip: Hold a vacuum cleaner wand next to the saw to catch the dust.
Ceiling Fan Installation Guides By Brand
When it comes to installing a ceiling fan, there is little difference between the various ceiling fan brands. However, certain brands and models have specifics that are worth explaining. Del Mar Fans invites you to read our brand-specific fan installation guides for our most popular brands, like Casablanca, Fanimation, and Hunter.
Also Check: How Many Presidents Were Democrats And Republicans
Wire Receiver And Supply Line
To connect the supply line and the receiver, follow the steps below:
Turn the connections up and push them through the hanger bracket into the outlet box. Separate the wire connections, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the box. Be careful not to pinch any wire connections.
Choose Dimmable Led Downlights
Make your lighting fixtures flexible so as to tune them according to your mood. Dimmer switches should be used to control lights in different zones. Also make sure to choose between cool white light and warm white light before you install light fixtures. This will save your time as you will have the right type of lights at the time of installation which will last longer without need of replacement.
Recommended Reading: Who Were The Radical Republicans And What Did They Believe
Installing Fanimation Zonix Fans
Installing the Zonix by Fanimation , a sleek, modern-looking fan, may seem like a daunting task, but it is quite simple. The places attach directly to the mounting without using blade irons, which helps to reduce the amount of work required to install the fan. All you will need is a Phillips-head screwdriver, wire strippers, and a ladder!
Del Mar Fans hopes that youve found our ceiling fan installation video and written guide to be helpful and informative. Be sure to read other articles in the Del Mar Fans Blog to learn more about maintaining fans, installing lighting fixtures, and improving your homes energy efficiency!
How To Install A Ceiling Fanbox With Brace
Once you have identified the ideal location for your new ceiling fan, you will need to gather the following tools and materials to replace the existing electrical box with a UL-listed outlet box marked “Acceptable for Fan Support”.
The outlet box generally supports up to 50 pounds. If your fan weighs more than 50 pounds when in motion, you will need a heavy duty brace for additional support. See Del Mar Fans & Lightings selection of ceiling fan mounting systems.
Recommended Reading: Presidential Tie Colors
Ceiling Fan Wiring Diagram
Take a closer look at a ceiling fan wiring diagram.
Pick the diagram that is most like the scenario you are in and see if you can wire up your fan! This might seem intimidating, but it does not have to be. With these diagrams below it will take the guess work out.
Need step by step instructions on replacing ceiling fan?
Using Your New Ceiling Fan
Using a ceiling fan with your air conditioning and heating system reduces energy consumption and increases utility bill savings. Some homeowners have reported an annual savings of $500. Remember, you may sacrifice a few hours to install a ceiling fan, but the comfort and savings is worth the time.
When you are ready to improve your home’s efficiency and try your hand at installing a ceiling fan, we welcome you to browse our selection of ceiling fans from the top brand names!
Don’t Miss: Who Controls The Senate Republicans Or Democrats
Best Hugger: Portage Bay Hugger 52 Matte Black West Hill Ceiling Fan
Diameter: 52 inches | Material: Metal, manufactured wood| Lighting: LED bulbs included | Control Type: Pull-chain | Mounting Type: Flush
-
Mounts flush to the ceiling
-
Reversible blades
-
Pull chain
Instead of hanging from a downrod, this hugger-style fixture from Portage Bay mounts flush to the ceiling and is just 11.5 inches tall. It’s ideal for folks with low ceilings and anyone who prefers the clean look of hugger fans.
This ceiling fan has five reversible blades with different finishes on each side, plus an integrated LED light kit. Though it doesn’t have a remote control, it’s easy to install and switch the blades around to your liking.
While choosing a ceiling fan is somewhat a matter of personal preference, we think the best overall option is the Hunter Fan 52” Dempsey 4-Blade Ceiling Fan with Remote Control , thanks to its stylish features and long-lasting LED bulb. If you’re looking for a budget pick, consider the Harbor Breeze Armitage Ceiling Fan . Despite the low price tag, it’s rated for rooms up to 400 square feet.
Make The Wire Connections
- Hook one side of the canopy onto the ceiling plate.
- Using twist-on wire connectors, join the two green wires to the bare copper wire coming from the cable.
- Join the two white wires.
- Then connect the two black wires.
- Swing the fan up into position against the medallion and secure it with the two canopy screws.
Recommended Reading: What Is Donald Trump Republican Or Democrat
